Create+ - 3Doodler

Create+ Troubleshooting Guide

Ross Downey — Wed, 04 Feb 2026 11:06:08 +0000

3Doodler Create+ Troubleshooting Guide (PDF)

Create+ Frequently Asked Questions

What type of filament can be used with the 3Doodler Create+ pen?

−

The 3Doodler Create+ pen is designed to use 3Doodler Create+ filament (ABS, PLA, FLEXY, and WOOD). They are straight-cut strands, 10″ long and 2.85mm in diameter. See all available options here.

Why is the light on my 3Doodler blinking/flashing red?

If you are experiencing a flashing red light with your 3Doodler, please contact our Customer Service team by emailing help@the3doodler.com, and we will be more than happy to assist you.

Why is the light on my 3Doodler always red?

After several minutes of being switched ON without engaging the motor, your pen will go into “standby mode.” The heat will cut off, and the LED will stay red until the device is made active again.

Reactivate the device active by single-clicking the FAST button or by turning the pen OFF and then on again. If your LED is still remaining red after this please contact our Customer Service Team.

My 3Doodler sometimes makes a slight crackling sound while extruding. Is this normal?

If the filament makes a slight crackling sound while extruding, this is totally normal. It is caused by a small amount of moisture (that was been caught in the strand during manufacturing) escaping from the filament strands. This is not dangerous or a cause for concern!

The filament is moving slowly. What do I do?

Sometimes, when you get to the end of one strand, extrusion slows noticeably. Put a new strand into the back of the 3Doodler pen. If it still extrudes very slowly (or not at all), try giving the new one a little nudge down, and that should do the trick!

Why is my 3Doodler Create+ having difficulty feeding/gripping a new strand?

The Create+ pen has two temperature settings that are meant for specific types of filament. Typically, we see jams occur when folks aren’t using the corresponding temperature setting for the filament type they select.

3Doodler PLA and WOOD filament should be used on the PLA temperature setting ONLY.

3Doodler ABS and FLEXY should be used on the ABS/FLX temperature setting ONLY.

If you’re using the correct filament/temperature setting combo, but your pen still won’t feed, try using your Unblocking Tool to ensure you don’t have a jam (instructional video here).

Why are my pen’s buttons not functioning as expected?

If your buttons aren’t functioning as intended, please contact our Customer Service team by emailing help@the3doodler.com and we will be more than happy to assist you.

The tip of my pen broke off! How do I re-attach the nozzle?

The Create+ instructions state that you should carefully change the pen tip when the pen is plugged in, turned ON, and fully heated up. Doing this can prevent the pen tip from breaking in the future.

Unfortunately we don’t have a way to repair pens with broken pen tips, so we’ll need to look into activating your Warranty. Please contact our customer service team.

The post Create+ Troubleshooting Guide first appeared on 3Doodler.

Create/Create+ Manuals

Ross Downey — Fri, 06 Feb 2026 10:52:25 +0000

Create+ 3D Pen Manual

English

Create+ Manuals – Alternate Languages (A-Z)

Chinese (Simplified)

Chinese (Traditional)

Create Manuals – Alternate Languages (A-Z)

The post Create/Create+ Manuals first appeared on 3Doodler.

Create+ Getting Started Guide

Ross Downey — Fri, 30 Jan 2026 11:09:14 +0000

Getting Started with your 3Doodler Create+

Not sure where to begin with your new Create+ pen? You’ve come to the right place. Let’s get started with a few of the basics. By the end you’ll not only be Doodling, but Doodling well.

Basics

Plug in Your 3Doodler

Ensure you select your temperature to ABS/FLX for ABS and FLEXY filament or PLA for PLA or WOOD filament.

Press Fast/Slow & Insert a Strand

Press either button to put your pen in drive mode, then insert a strand of filament into the back of the pen. Push gently to ensure it engages with the gears and grips properly.

Ready, Set, Doodle

It may take a few seconds for your filament to extrude.

The Buttons

Fast / Slow Button

Single click either Fast or Slow button to start a continuous flow of filament. Click either button once to stop the continuous flow.

Reverse Feature

Double click either button to reverse the strand. The pen will pulse, which helps it reverse properly. If the strand is too short, carefully remove the nozzle and use the unblocking tool to push it out.

Feeding Strands

First try pushing your filament gently into the pen to ensure it engages with the gears. If the strand inside the pen is not long enough to grip or push by hand, use another filament strand or the unblocking tool to push it into the gear system.

Jammed Filament

Using the Included Screwdriver

Though uncommon, filament can become jammed (often due to unsnipped filament ends). While the maintenance cover should only be opened when absolutely necessary, following the instructions in the manual will keep you safe.

A Few Reminders

Follow the step-by-step user manual at all times.
Never force anything into place.
Ensure there is no filament inside the pen when replacing the maintenance cover.
Align tabs carefully when reattaching the cover.

Still Struggling?

Don’t worry, our support team is here to help. Please reach out to us here.

Pressing on Surface

If filament won’t hold to paper or moves unpredictably, push the nozzle firmly onto the paper and allow filament to extrude for a couple of seconds, then lift the nozzle. The extra pressure helps the filament stick. We call this “anchoring.”

Incorrect

Filament bunches when not properly anchored to the surface.

Correct

Press the nozzle firmly onto the surface and hold briefly before lifting.

Nozzle Removal

Use the nozzle removal tool to gently unscrew the nozzle counter-clockwise while the pen is turned on and fully heated. Do not over-tighten the nozzle and keep the tool centered to avoid damaging the threads.

Step 1

Position the nozzle removal tool around the nozzle base.

Step 2

Gently unscrew counter-clockwise until the nozzle is free.

Tips

Keep Your Filament Clean

Use clippers or scissors to snip melted filament ends to avoid unnecessary jams.

Welding Filament

While extruding, touch the tip to both pieces to weld them together.

The post Create+ Getting Started Guide first appeared on 3Doodler.